LTC4223CDHD-2#PBF【PDF 16/24 页】IC CNTRLR HOT SWAP DUAL 16-DFN

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录42

12页 13页 14页 15页 [16页]17页 18页 19页 20页

LTC4223-1/LTC4223-2

422312f

APPLICATIONS INFORMATION

GATE Pin Voltage

The gate drive at 12V

GATE

is compatible with any logic

level MOSFET. The guaranteed range of gate drive is 4.5V

to 7.9V, with a typical of 6.2V.

Active Current Loop Compensation

The compensation network consisting of resistor R

and

gate slew rate control capacitor C

stabilizes the internal

active current limit circuit. The value of C

is selected based

on the inrush current allowed. The suggested value for

is 47? The value of C

should be d330nF and R

between 10?and 100?for optimum performance.

High Side Current Sense

The 12V load current is monitored via the voltage across an

external sense resistor. The LTC4223 features a high side

current sense ampli er that translates the sense voltage

from the positive rail to the negative rail using a resistor

ratio of 33 times. The output voltage at 12IMON pin can

then be fed into an LTC1197L ADC as shown in Figure 10

for data conversion. The current sense information can be

used by the system controller to manage the power budget

allocated to the modules on the card. Full scale input to

the current sense ampli er is 82.5mV, corresponding to

an output of about 2.7V. If the input exceeds 100mV, the

output clamps at 3.2V.

Supply Filtering

The internal circuitry of the LTC4223 is powered from the

pin. Bypass V

with at least 330nF to ground. If V

is derived from the same supply as is AUXIN, include a

decoupling resistor as shown in Figure 11. This RC net-

work allows the V

pin to ride out supply glitches caused

by short circuits on the auxiliary output or on adjacent

boards, thus preventing an undervoltage lockout condi-

tion on V

. Since the absolute maximum rating for V

is 7V as compared to 10V for AUXIN, select R2 and C2 to

keep the peak voltage seen by V

below 7V during any

voltage spikes.

FAULT

TIMER

AUXOUT

12V

OUT

TMR

422312 F08

10糀

5 6 7

2糀

FAULT PULLS LOW DUE TO AUX

OVERCURRENT FAULT AFTER POWER UP

START OF COOL-OFF CYCLE

START OF

DEBOUNCE CYCLE

RESET FAULT HIGH

FAULT PULLS LOW AND RESTART OF

COOL-OFF CYCLE DURING POWER UP

END OF DEBOUNCE CYCLE

START AUX INTERNAL GATE RAMP WHEN STARTUP CONDITIONS ARE MET

AUX OUTPUT IN CURRENT LIMIT

RESTART OF

DEBOUNCE CYCLE

COOL-OFF CYCLE

DEBOUNCE CYCLE

FILTER DELAY

COOL-OFF CYCLE

2糀

10糀

AUX INTERNAL GATE REGULATES

Figure 8. Auto-Retry after AUX Overcurrent Fault

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式